REMODEL ESTIMATOR  Version 2.46 Shareware. 
Copyright 1990-97 (C) CPR International, Inc.
Tel: (510) 654-8338    Fax: (510) 652-6067.
E-Mail: cpr@cprsoft.com  Internet: http://www.cprsoft.com
*********************
Please note the following:

1. Hardware requirements.
Remodel Estimator full registration system requires a compatible
PC with minimum 384K RAM memory.

2. Program Installation.
If you receive a copy of the shareware program on a disk, 
follow the following steps to install the system.

	a. Insert shareware disk in drive A (or B)
	b. At DOS prompt A> (or B>), type:

	        INSTALL     (press Enter)

Then follow screen prompts and instructions.

3. If you download from a bulletin board or AOL, follow the 
following steps to install the system:

	a. Unzip the REMODEL.ZIP file usink PKUNZIP command of the 
	PKZIP (by PKWARE) shareware program as follows:

		PKUNZIP REMODEL

	b. After unzip is complete, at the C: prompt of download
	directory, type:

		INSTALL  	(press Enter)

Then follow screen prompt and instructions.

4. To run Remodel Estimator shareware:
Go to the directory where shareware is installed. Default is C:\reshare).
At DOS prompt, type:

        REMODEL           (press Enter)

5. Cost indexation for various cities and states.
Thes full registration version of the system comes with a program called
"citindex".  This program will adjust your cost database for cost indexes
in all states and for several cities in the same state, if applicable.
Cost indexes are applied for each of the CSI 16 divisions. Furthermore,
the user can modify existing indexes provided.

6. The full registration version of the Remodel Estimator (Remodel Pro)
also contains additional features such as 'Bill of Material' reporting,
expanded cost data updated for current year, additional sample cost 
estimates, on-screen Help system and more.

7. Important Notice to Microsoft  MS-DOS operating system 6 users.
Microsoft MS-DOS 6 users, note the following information supplied by
Microsoft Corporation for Clipper compiled programs.

"After you upgrade to MS-DOS 6, a "not enough memory" error message may
appear or your system may stop responding (hang) when you try to run an
application generated with Computer Associates' Clipper program.

To correct this problem, add the NOEMS and NOVCPI switches to the EMM386.EXE
command in your CONFIG.SYS file. For example:

	device=c:\dos\emm386.exe noems novcpi

The application generated with Clipper should now run on your system.

More Information:
You can also work around this problem by using the RAM switch instead of the
NOEMS switch with EMM386 or you can remove the DEVICE= statement for
EMM386.EXE from your CONFIG.SYS file.

EMM386 is a Virtual Control Program Interface (VCPI) server. VCPI is a
program interface that allows expanded memory services (EMS) emulators and
DOS extenders to coexist within a 80386/80486 environment."

CPR note:
The above MS-DOS correction issued by Microsoft for MS-DOS users is
applicable to CPR programs since all CPR Estimating and Jobcost programs are
Clipper compiled.  If you do not use MS-DOS 6, save this note for possible
future reference.

CPR International, Inc.
(510) 654-8338
**********************************
Installation instructions:
1. To install on computer: Insert disk supplied in drive A (or B).
At DOS prompt A> (or B>), type
   INSTALL   (press ENTER)

2. To start program, go to your shareware directory (default is C:\PCSHARE).
Then type PCEST.
Questions, comments, support:
Contact CPR, Inc., P.O. Box 3465, Berkeley, CA 94703   Tel:(510)654-8338
****************************
